1100 1200 model 500kg per hour water wet pan mills to Africa
Wet pan mill, also called gold grinding machine, water pan mill,
gold round mill, chilean mill, and wheel grinding machine. It is
mainly used for grinding gold, silver, lead, zinc, iron, copper and
other ores after they are crushed. All ores that can be processed
by ball mills can be used by wet pan mills. The final product size
is less than 150 meshes which is suitable for the next
beneficiation process. 1100 1200 model wet pan mill have become a
popular gold grinding mill machine for small and medium gold miners
due to its advantages of easy installation, high capacity and low
investment in mining sites such as Sudan, Zambia, Mauritania, Saudi
Arabia, Egypt ,Nepal.
Product picture
Working principle
Wet pan mill mainly through the raw material stirring, rolling,
crushing, rolling repeatedly to achieve water balance, uniform
ratio, low gas content, improve the molding rate and molding
quality, through the machine grinding material molding products,
with high density, good strength, no porosity ratio and other
characteristics. High efficiency and energy saving, high output,
the product is used for the recovery of tailings in the iron ore
process, does not make the loss of mineral powder, so that
effective resources can be fully utilized.
Main Features of Wet Pan Mill
1. The casting are made of high manganese steel liner, which
greatly increases the service life and increases the capacity by
30%-60%.
2. The whole set of equipment and castings are installed by small
parts, so that they do not require large lifting equipment in
remote mining areas, are not affected by the site, and reduce
labor.
3. Increase the weight of the grinding wheel and reduce the area of
thrust surface. The rotation of the grinding wheel increases the
pressure of the crushed ore, thereby increasing the capacity.
4. It can be produced by a single machine or in groups, and it can
achieve the same grinding result as a ball mill, but the cost is
much lower than the ball mill.
5. The machine adopts a new gearbox and soft start device, which
saves energy and reduces production costs.
Specification
| Model | Type
(mm) | Max feed
size (mm) | Capacity(t/h) | Power(kw) | Weight(ton) |
| 1600 | 1600x350x200x460 | ＜25 | 1-2 | Y6L-30 | 13.5 |
| 1500 | 1500x300x150x420 | ＜25 | 0.8-1.5 | Y6L-22 | 11.3 |
| 1400 | 1400x260x150x350 | ＜25 | 0.5-0.8 | Y6L-18.5 | 8.5 |
| 1200 | 1200x180x120x250 | ＜25 | 0.25-0.5 | Y6L-7.5 | 5.5 |
| 1100 | 1100x160x120x250 | ＜25 | 0.15-0.25 | Y6L-5.5 | 4.5 |
| 1000 | 1000x180x120x250 | ＜25 | 0.15-0.2 | Y6L-5.5 | 4.3 |
Wet pan mill operating rules
1. The operator must be trained by the manufacturer and fully
understand the structure and performance of the machine before they
can operate. The operator must comply with the relevant safety and
shift transfer system.
2. Before work, strictly follow the lubricating oil regulations to
refuel, and keep the oil amount appropriate, the oil circuit
smooth, and the oil injection port clean.
3. Check whether the circuit, electrical parts, line connectors,
switches are solid and complete. If there is damage, it must be
repaired and replaced.
4. Check whether the parts of the machine are intact, whether the
roller rotates flexibly, the tightness of the transmission belt,
and whether the transmission parts are securely connected; After
the inspection is completed, the boot idling for 3-5 minutes,
confirm that the parts are normal, before adding the ore, and must
be added in strict accordance with the prescribed amount of ore, it
is strictly prohibited to overload work.
5. When feeding the ore, the material must be sifted to prevent
hard metal debris such as iron blocks from being put into the mill
and damaging the machine.
6. When stopping for some reason, the material in the roller should
be removed first, and then started. It is strictly prohibited to
forcibly start with heavy load.
7. When the machine is in operation, the operator shall not leave,
and should often inspect the working conditions of various parts.
In case of abnormal sound of the equipment, large vibration of the
roller, excessive temperature of the reducer oil, overheating of
the motor housing, and slip of the transmission belt, the machine
should be shut down immediately.
8. During the shutdown process, when the roller is not completely
stopped, it is not allowed to extend the arm and other instruments
into the roller basin to prevent injury and damage to the machine.
Spare Parts
Working site
We also supply
Contact us
